Machine Details Page - Revision history

Taylor: added more spacing so it looks a bit nicer.

2020-09-28T07:35:04Z

added more spacing so it looks a bit nicer.

2020-09-28T07:33:25Z

added image

2020-09-28T07:29:04Z

added section relating to list population with all errors.

2020-04-16T11:46:03Z

Clarified what the final two rows in the table do

2020-04-16T11:44:19Z

Initial content.

2020-04-16T07:06:02Z

added a small picture of the symbol for downloading pie charts for utilization.

2020-04-16T06:50:02Z

Settings area

2020-04-16T06:48:24Z

Map area

2020-04-16T06:46:51Z

Map area

2020-03-24T15:20:28Z

Pavers: information added for static/transport and idle for pavers

@@ Line 103: / Line 103: @@
 This report is available for high level users. It shows a historical view of the errors. By default, the errors are listed in a table, in sequential order, with the newest at the top of the list. If the same error keeps repeating every minute, without any other errors in between, then the list will only show the last time it was reported.
 [[File:2020-09-28_09_31_44-Full_CAN-bus_Error_Report.png|200px|thumb|left]] If you are required to see all of the errors, including the repeated ones, please click the link that says "Show list with duplicates". After clicking this, it could take a long time to populate the list (up to several minutes). Once the page loads, you will see all errors that were reported from the machine.
 === Notes ===

@@ Line 102: / Line 102: @@
 ==== Full CAN Bus Report ====
 This report is available for high level users. It shows a historical view of the errors. By default, the errors are listed in a table, in sequential order, with the newest at the top of the list. If the same error keeps repeating every minute, without any other errors in between, then the list will only show the last time it was reported.
-If you are required to see all of the errors, including the repeated ones, please click the link that says "Show list with duplicates". After clicking this, it could take a long time to populate the list (up to several minutes). Once the page loads, you will see all errors that were reported from the machine.
+[[File:2020-09-28_09_31_44-Full_CAN-bus_Error_Report.png|200px|thumb|left]] If you are required to see all of the errors, including the repeated ones, please click the link that says "Show list with duplicates". After clicking this, it could take a long time to populate the list (up to several minutes). Once the page loads, you will see all errors that were reported from the machine.
 === Notes ===

← Older revision		Revision as of 07:29, 28 September 2020
Line 99:		Line 99:

	=== Alerts ===		=== Alerts ===
		+
		+	==== Full CAN Bus Report ====
		+	This report is available for high level users. It shows a historical view of the errors. By default, the errors are listed in a table, in sequential order, with the newest at the top of the list. If the same error keeps repeating every minute, without any other errors in between, then the list will only show the last time it was reported.
		+	If you are required to see all of the errors, including the repeated ones, please click the link that says "Show list with duplicates". After clicking this, it could take a long time to populate the list (up to several minutes). Once the page loads, you will see all errors that were reported from the machine.

	=== Notes ===		=== Notes ===

@@ Line 96: / Line 96: @@
 ==== Table area ====
-This area explicitly shows the values that are used to create the Pie Charts. A summary of the values in the table is shown in the bottom rows.
+This area explicitly shows the values that are used to create the Pie Charts. A summary of the values for the selected period is shown in the second to last row of the table. In the final row of the table, the total values for the lifetime of the machine are shown.
 === Alerts ===

← Older revision		Revision as of 11:44, 16 April 2020
Line 95:		Line 95:

	==== Table area ====		==== Table area ====
		+
		+	This area explicitly shows the values that are used to create the Pie Charts. A summary of the values in the table is shown in the bottom rows.

	=== Alerts ===		=== Alerts ===

@@ Line 30: / Line 30: @@
 ==== Chart area ====
-The chart area shows two pi charts, side by side. On the left side, the chart shows the utilization over the time period that you selected in the [[#Settings area|settings area]]. On the right side, the chart shows the utilization of the machine over the lifetime of the machine. In the upper right of each chart there is a small symbol with three lines, if clicked this allows you to download the graphic.
+The chart area shows two pi charts, side by side. On the left side, the chart shows the utilization over the time period that you selected in the [[#Settings area|settings area]]. On the right side, the chart shows the utilization of the machine over the lifetime of the machine. In the upper right of each chart there is a small symbol with three horizontal lines ([[File:Hamburger small.png|30px]]), if clicked this allows you to download the graphic.
 Depending on what type of machine you are using the charts will change slightly. To understand what each section of the chart represents please consult the corresponding section below.
@@ Line 49: / Line 49: @@
 Hours are accumulated when the following conditions are met:
 * Engine RPM >= 1100 rpm (greater than 1100 RPM)
 ====== Idle ======

@@ Line 22: / Line 22: @@
 ==== Settings area ====
-In the settings area, you can select the length of time to generate the graph for. Your are able to select one of the following ranges of time:
+In the settings area, you can filter the length of time to generate the graph for. Your are able to select one of the following ranges of time:
 * 1 day
 * 1 week
 * 1 month
-Once you have selected a range of time, you are able to select the start for this range of time. For example if you select 1 week, then 24/9/2019 you will get a graph that shows the utilization data for an entire week starting on 24/9/2019.
+Once you have selected a range of time, you should select the start for this range of time. For example if you select 1 week, then 24/9/2019 you will get a graph that shows the utilization data for an entire week starting on 24/9/2019.
 ==== Chart area ====

@@ Line 18: / Line 18: @@
 ==== Map area ====
-When viewing the map area, in the machine utilization, the map gives an overview of where the machine was physically located during the selected period.
+When viewing the map area, in the machine utilization, the map gives an overview of where the machine was physically located/working during the selected period ([[#Settings area|settings area]]).
 ==== Settings area ====

@@ Line 46: / Line 46: @@
 ====== Static/Transport ======
 ====== Idle ======
 ====== Paving ======
-For a paver to be considered paving, it must meet the following conditions:
+Hours are accumulated when the following conditions are met:
 * Driving forward
 * Not in Transport mode